cube ice in commercial ice making machine
Why Is My Commercial Ice Machine Not Making Ice?
A problem with your ice is ultimately going to be a problem with your reputation. This could lead to your ice maker not being filled to capacity, or the ice machine not producing ice at all. If pressure is too low, the water does not flow through to the ice maker to create ice. Regardless, whether or not the ice maker cycles into freezing during this phase of the call, monitor the water flowing in to refill it, and ensure that it stops.
Some ice machines will continue filling with just a bit more water once the machine cycles into freeze, but if the ice machine continues to fill up until it has a consistent flow from the drain pipe, inspect the fill solenoid. If your ice machine has a water filter (and it should), check that it is not blocked, limiting the flow. Check to see that your water delivery valve is not closed, or restricted, by brackets or shackles. When your ice machine does not stop making ice, check shutoff arms & switches, the water intake valve, and control modules.
If you notice that there is frost or ice accumulation within the machine, and the machine is not stopping making ice, the water inlet valve must be tested for electrical and mechanical failure. You can test valve continuity and test inline water pressure to conclusively determine whether a part is defective. If you suspect a faulty stem in your ice machine, such as a contaminated water filter or an errant water intake valve, then you should call a water appliance repair professional. Make sure to change your water filter at all times, and to clean any parts in your ice machine.
If the machine is air-cooled, see if you need to clean the condenser unit or have it replaced. Failing to clean your condenser on a regular basis could result in machine jams and other annoyances for ice quality and production. If you are still not getting any ice after checking to make sure the ice dispenser is powered and the correct temperature, a frozen or clogged water line may be to blame.
This issue is irrelevant if you find no unusual accumulation of ice or freeze inside your unit.
Frozen, unusual accumulations of ice inside a machine can cause the release arms, springs, and other components to become stuck. This will result in longer periods during ice machines discharge cycles, can cause a tripping of a solid-state controller due to an error of long-cycle times, and increase ice production costs.
If your ice machine is not cold enough to freeze the ice, the ice machine will not know when to produce another batch. If your commercial ice machine is not making as many cubes as it used to, you will have to call the business appliance repair crew to see what may be wrong. If you have replaced your filters and the machine is still not making ice, then you may need to call a professional commercial ice maker repair team in Panama City, Florida. You can defrost a commercial ice machine by turning it off, as well as turning off your water supply.
The best solution for avoiding being faced with an uncomfortable surprise when your ice maker is off is you understand how to keep it up, and specifically, to completely clean it out before turning it off, if that is what you want. As we suggested in our earlier post that describes what is an ice maker, routine maintenance is the best way to prolong the lifespan of your machine. Poor maintenance will cause your machine to operate less effectively, either because of pollution or wear.
Often, just turning down your AC or moving the boxes further from the ice machine will allow the machine to run at its best. If the machines thermostat is registered too high, it could impact the machines ability to produce an appropriate volume of ice. If the location is above its recommended temperature, every machine is not capable of producing its maximum amount of ice.
If possible, move the machines to cooler locations, and observe whether your machines thermostat drops. Check if you have to adjust a control arm in order to power your machine back on and restart the ice output. If your ice machine does not turn into freezing mode when the floating switch is lifted, or water has reached a level probe, then the operation of the floating switch assembly or the level probe needs to be checked.
You need to adjust the amount of water that the machine uses to fill up a mold on each filling and freezing cycle. If this ice machine problem is with a water-cooled machine, check to see if there is any water flowing, that the water is not warm, check that the header pressure regulator valve has not gone off-set or completely failed, and if possible, remove the water lines and check inside the condenser for any clinging ice or mud. If ice seems to drop too slow from the evaporator, and harvesting pressure is good, test the strong flow of water in your Hoshizaki ice machine while it is harvesting, and check the distribution nozzles are clean. You should replace your water filters every six months if your water is strong, or every 12 months if not.
If temperatures look good, but water is freezing before reaching your ice machine, an expert can help with Delaware restaurant equipment repairs. If you tried these tips to fix ice makers, and the ice makers are still not working, reconnect the fridge and use Appliance Repair OKC Services flexible repair schedule for refrigerator repairs. If all is working correctly, continue to plug the fridge in and wait a couple hours to see if there is any ice.
To schedule ice maker repairs in Oklahoma City contact Appliance Repair OKC Services by calling 405-378-4566 or visit our website at https://www.okcappliance.com to also our Google business page at https://cutt.ly/YEnc8qk. Call now!